®ANINDEPENDENTLABORATORYTESTINGFORPUBLICSAFETYG 028Read this manual and all labels carefully beforeoperating your powder actuated tool. This manualsho
10101437482-58YELLOW?BROWN?GREEN?GRAY?G 0182. Remington power loads are available in four power levels with gray (1) being the lowest powerlevel and y
11101437482-59G 018Safety Precautions6. Power fasteners are a permanently installed fixture. An act of demolition is required for theirremoval. Approp
12101437WHY A POWER FASTENER HOLDSIN CONCRETEThe compression bond of the concrete to the power fasteneraccounts for the majority of the holding power.
13101437FASTENING INTO CONCRETEThe proper power fastener length can be determined by adding thethickness of the material to be fastened and the amount
14101437Operation1. Grasp muzzle and slide barrel forward rapidly until it stops. This sets piston into firing positionand opens the chamber.4. Push b
15101437WATEROperation5. Place the muzzle of tool perpendicular to work surface without tilting the tool. Push tool againstwork surface until sliding
16101437TangTang SpringTang CapBufferMuzzle CapPistonBarrelReceiverMaintenanceTroubleshooting GuidePROBLEMPiston rod hangs out of muzzlecap.Overdrivin
17101437Troubleshooting Guide (cont.)PROBLEMTool does not completelydepress.Tool does not fire.Opening and closing of barrelor pushing down of the too
18101437Parts List – Model 494KEY PARTNO. NO. DESCRIPTION QTY.1 101123-01 Screw, 1/4"-20 x 1.25 22 101122-01 Washer 23 101128-01 Handle & Tri
19101437AccessoriesDISASSEMBLY1. a) Remove tang cap, tang spring, and tang.Slide barrel assembly from receiver.b) Remove muzzle cap from barrel by un-
2101437Maximum 3" (76 mm)* Not provided with toolPower Load*TriggerMuzzle/GuideRecommendedApprovedGoggles*Power Fastener*Spall ShieldBarrel Assem
20101437Tool Disassembly and AssemblyWARNING: Always unload a powder actuated tool before disassembling, replacing barrel,cleaning, or assembling.!WAR
21101437Buffer and Piston Replacement!WARNING ICON G 001WARNING: Always unload a powder actuated tool before disassembling, replacing barrel,cleaning,
22101437482-81aTwo by foursFurring stripsMetal electricaljunction boxesConduit clipsShelf brackets1/4" Plywood orpegboardFor fastening thisPower
23101437Application ChartIMPORTANT• If power fastener goes below the top surface of the board, use penetrating control disc (* seeillustration below).
Limited Warranty AgreementDESA International warrants the Remington Model 494 Powder Actuated Fastening Tool againstdefects in materials and workmansh
3101437Warning: Safety PrecautionsThe following pages contain detailed warnings, cautions, and rules of safe operation.Read carefully and become famil
4101437482-12G 018G 018G 018Safety Precautions5. ALWAYS make sure the work area is clean from loose material and debris.2. NEVER place your finger on
5101437482-19482-24G 018G 018G 018G 018Safety Precautions3. ALWAYS store UNLOADED powder actuated tool and power loads in a locked container. Keeppowe
6101437TOO HARDPointflattens482-29???482-25TOO BRITTLESurfaceshatters482-30TOO SOFTSinks inwithaveragehammerblow482-28G 018G 018G 018G 018Safety Preca
7101437CAST IRON GLASSTILEBRICK482-33Safety Precautions3. NEVER make fastenings in spalled or cracked areas.2. NEVER attempt to drive power fasteners
8101437TOO THINWELD482-40G 018G 018Safety Precautions7. DO NOT drive power fasteners into steel base material less then 3/16" thick, within 2&quo
9101437POWERLOADSPOWERLOADS482-49GASOLINEGASOLINE482-50G 018G 018G 018G 018Safety Precautions2. Should the tool fail to fire, hold the muzzle firmly a
Comments to this Manuals